How Do You Match a Stub End to a Lap Joint Flange?

Sep 15, 2026 Leave a message

A stub end and a lap joint flange must be purchased as a working pair. Matching only the nominal pipe size can leave the flange unable to seat behind the lap, the weld end mismatched to the pipe wall, or the assembled joint incompatible with the mating flange and gasket. Buyers should verify the governing standards, dimensions, pressure-temperature rating, materials, and inspection documents before approving the combination.

Understand what each component does

The stub end is welded to the pipe and provides the lap that the backing flange bears against. Its front surface participates in the gasketed joint. The lap joint flange slides over the pipe before welding and remains free to rotate, which helps align its bolt holes with the mating flange.

Because the two pieces perform different functions, their specifications are also different. The stub end follows a fitting material and dimensional specification, while the backing flange follows a flange standard with a material group and pressure class. A complete inquiry names both components instead of requesting a "lap joint flange set" without defining the parts.

Choose one compatible standard system

Begin with the project piping class and design code. For an ASME-based order, ASME B16.9 covers overall dimensions, tolerances, ratings, testing, and marking for factory-made wrought butt weld fittings. ASME B16.5 covers pressure-temperature ratings, materials, dimensions, tolerances, marking, testing, and flange-joint provisions for the sizes within its scope. State the required edition of each standard on the purchase order.

MSS SP-43 is a separate standard practice for wrought and fabricated butt weld fittings in low-pressure, corrosion-resistant applications. Its current scope covers fittings for Schedule 5S or 10S pipe, while also showing short-pattern stub ends suitable for Schedule 40S. A buyer should not select SP-43 merely because the line is stainless steel; the service, wall, design code, and approved piping specification must support that choice.

Do not assume that a stub end made to one standard will automatically match a flange or project detail based on another. If mixed standards or a proprietary design are necessary, require a dimensioned assembly drawing and engineering approval before manufacture.

Match these dimensions as an assembly

The supplier should compare the stub end, backing flange, pipe, gasket, and mating flange on one dimensional review. The most important checks are:

Purchase variable What must match Why it matters
Nominal pipe size Stub end, lap joint flange, pipe, gasket, and mating flange use the intended NPS. NPS is the first compatibility check, but it does not confirm the remaining geometry.
Pipe wall or schedule Stub-end weld wall and bore suit the ordered pipe wall and permitted internal transition. A mismatch can complicate fit-up and welding even when NPS is correct.
Lap outside diameter The lap fits the backing flange and provides the specified gasket seating area. Too little or excessive overlap changes how the joint seats and transfers load.
Lap thickness and profile Thickness, face profile, and transition conform to the selected standard or drawing. These dimensions affect flange seating and the final face position.
Flange bore and corner radius The flange clears the pipe and stub-end transition while bearing properly on the back of the lap. Interference can prevent full contact or free rotation.
Stub-end length Long or short pattern, and dimension A, suit the flange class, welding access, insulation, and project layout. An unspecified pattern can create an assembly or access problem.
Bolt circle and holes The lap joint flange matches the NPS and class of the mating flange. Rotation helps alignment; it cannot correct a different drilling pattern.

The butt weld end also needs a defined preparation. ASME B16.25 covers the preparation of butt welding ends, including bevels and internal or external shaping for applicable joints. State any project-specific bevel, root face, bore transition, or matching requirement rather than assuming that "standard ends" has only one meaning.

Check the gasketed face and flange rating

The gasket seals against the stub-end lap, so the purchase order must define the required facing, surface finish, and gasket arrangement in accordance with the piping specification. Confirm that the effective gasket contact area is supported and that the gasket inside diameter does not intrude into the intended flow bore. The mating flange facing must be compatible with the complete joint design.

Pressure class belongs to the flange system and is not interchangeable with pipe schedule. Select the lap joint flange class, material specification, and bolting for the design pressure and temperature under the governing code. The lowest-rated relevant component or joint limitation controls; a heavier pipe wall does not upgrade an incorrectly selected flange.

Specify stub-end and backing-flange materials separately

The stub end is normally selected to meet the line material specification because it is welded to the pipe and exposed to the process. The backing flange may sometimes use a different approved material because it sits behind the lap, but this is an engineering decision. Temperature capability, flange rating, external corrosion, coating, galvanic interaction, and maintenance environment still need review.

Write the material standard and exact grade for each component. Descriptions such as "stainless stub end with carbon steel flange" are incomplete because they omit grade, product specification, flange class, heat treatment or coating requirements, and document expectations.

Put the complete pair in the RFQ

A concise purchase description can follow this structure:

Stub end: [NPS], [schedule or wall], [long/short pattern], [dimensional standard and edition], [material standard and grade], butt weld end per [standard or drawing]. Lap joint flange: [same NPS], Class [rating], [ASME B16.5 edition or approved flange standard], [material standard and grade], with compatible bore and corner radius. Joint: [facing and finish], [gasket specification], [bolting specification]. Submit a dimensioned assembly drawing, material certificates, and required inspection reports for approval.

For nonstandard combinations, add the pipe outside diameter and wall, lap outside diameter and thickness, radius, stub-end length, flange bore, facing details, and tolerances directly to the drawing. A simple section view often resolves more ambiguity than a long text description.

Review the pair before shipment

  • Confirm both items use the ordered standard editions, NPS, pattern, class, and materials.
  • Compare the flange bore and radius with the stub-end neck and back-of-lap transition.
  • Check the weld-end wall, bore, and preparation against the mating pipe.
  • Verify the lap face, finish, gasket dimensions, mating flange, and bolting as one joint.
  • Match markings and heat or lot numbers to the required material and inspection documents.
  • Resolve deviations on the assembly drawing before releasing the parts for fabrication.

To identify the exact pair for an inquiry, review Jiede Pipeline's Stub Ends and Lap Joint Flange product pages. Send the piping class or approved drawing with the RFQ so the required standard, dimensions, pressure class, materials, and documents can be checked together.