How Do You Specify Flange Face Finish for a Gasket?

Nov 17, 2026 Leave a message

Specify the gasket seating surface on both flanges: the facing geometry, the required roughness parameter and range, the machining pattern, and the way the finish will be checked. Take those requirements from the approved joint specification and the selected gasket. An offer that says "raised face, 125–250 finish" still leaves the buyer guessing what the numbers measure and whether the finish matches the gasket.

Start with the joint and the actual gasket

Use the project piping class and equipment drawing to identify the flange standard and edition, facing, and mating component. ASME B16.5 provides the dimensional and rating basis for flanges within its scope. On the order, identify the gasket style and material or reference the approved gasket data sheet. Check the finish on the valve, nozzle or existing flange as well, even if only one new flange is being purchased.

Facing geometry and surface finish answer different questions. A raised face defines where a gasket seats. Its finish describes the texture of that seating surface. A ring type joint uses a metal ring in matching grooves; specify the applicable groove geometry and finish at the sealing surfaces. A roughness range intended for a spiral wound gasket on a raised face should not be carried across to an RTJ groove.

Write the parameter, units and machining pattern

Ra is the arithmetic average of the absolute profile deviations from its mean line over the evaluated length. Write the parameter and units together, for example "Ra 3.2–6.3 µm" if that is the approved range. Converting 125 microinches Ra to about 3.18 micrometres Ra changes only the unit. RMS roughness, also called Rq, weights profile deviations differently; a number reported as RMS or Rz cannot be converted to Ra by changing the units. Ask the bidder to clarify any unspecified parameter.

State the required lay, or direction of the machining marks, separately. Concentric serrations form separate rings; a spiral finish follows a continuous track. Garlock's guidance on flange texture discusses both patterns. If the project calls for one pattern or specifies groove spacing, carry it onto the order. Two faces can have the same Ra value with different machining patterns.

Use recommendations for the specified gasket

For example, Flexitallic's spiral wound gasket guide recommends a turned surface in the range of Ra 3.2–6.3 µm for its stated application. Use that as an example of a complete roughness callout, not as a range for all seals. A polished face can fall below a specified lower limit, just as a rough face can exceed the upper limit.

If the flange specification and the gasket supplier's documented recommendation appear to conflict, send both requirements to the joint designer for resolution before ordering. Waiting until machining is complete can leave a choice between rework and changing an approved gasket. Neither change should be made by the bidder without review.

Quotation wording What is missing Request before award
"125–250 finish" Parameter and units Restate the range with both labels.
"Ra as specified" Pattern and surface to be checked Identify the specified lay and seating area on the drawing.
"Finish checked" Method and acceptance evidence Confirm the inspection basis and the record to be supplied.

Consider a drawing that requires concentric serrations. A bidder might quote the correct Ra range but offer a spiral cut. List that difference as a deviation for review before comparing the offers. Ask the bidder to mark the gasket seating band on the drawing, particularly when the flange has more than one machined surface. A finish note for the outside diameter cannot be used to accept the face.

Agree how the finish and damage will be checked

Follow the verification method in the applicable standard or agreed inspection plan. For example, Flexitallic's guide describes checking finish with a surface comparator. When an order also requires instrument readings, agree the parameter, trace direction, cut-off and evaluation length, location, sampling and report format. Mitutoyo's guide to surface profiles explains why the direction relative to the machining marks and the filtering of a trace affect the result. A comparator result and a set of numerical readings are different deliverables.

Review surface damage separately. A local groove or scratch that crosses the gasket seating band can create a path for leakage even when the surrounding texture meets the roughness requirement. Check also for dents, pitting and any flatness issues covered by the acceptance criteria. If an existing mating face is damaged, obtain an engineering disposition before specifying rework or substituting a gasket.

Define how shop and receiving records will identify each inspected flange or lot. Photographs can document damage or lost face protection, but they cannot replace the agreed finish check. When a face is disturbed after inspection, record what happened and confirm whether reinspection is required.

Put the finish on the purchase line and protect it

Add these fields to the normal flange designation. Use project values rather than copying the example range:

  • Facing type and drawing reference identifying the gasket contact area.
  • Approved gasket type, roughness parameter and range, units, and machining pattern.
  • Inspection method, sampling, surface defect criteria, and required report.
  • Clean face protection for handling and transit, with a check on receipt.

When enquiring about Jiede's weld neck flanges, provide the flange designation, mating face information and gasket data sheet with the finish requirement. Ask the supplier to identify any exception in the quotation so that it can be resolved before machining.